今日，日よう日[九月七日]，この　言葉が書く　実は書く言葉がないとおもう
むぞかしだとなにも考えないから，まいいか, 寝むい,寝る
03:01 位，目がさめて, 体が聞かない，一寸　弱い，少ない寝るだから
これは始めて，体　が　余り　元気 じゃない　でも　”sahur”  食べなきゃ
起きて，ご飯を食べに行きます，行ってきます
じゃなくって，ご飯　を　買って行きます、行ってきます
五ぽん位ただ今戻った、そして, ご飯 を食べる，お腹があまり元気じゃない
からい食べ物が選ばなかった，今順番は魚や，とふや，野菜　を食べる
いま食べてる[03:45]
今日は，予定がある、友だちと一緒に夜ご飯を食べる，楽しいみ。。。、プレレト　で
この所へ行った時がない，楽しいみ。　と感じ, 出来るとおもう
所に，早くなきゃ、時かん　が　そろそろ　終わる，買ったおちゃはまだ飲んだ。。。
早くしろよ。。と感じ
頑張らなければならない
あついおちゃをのでる
“imsyak” て　言って　聞いた、でことはそろそろ時かんが終わる，実は “imsyak” の事
がありません
“adzan” 聞いてる時、それは本者サイヌ,　時かん　が　終わる　だ
時間がもすぐ終わる。。。時間が終わる，時間がおえあった

寝るつづく
朝[06:06]へやにある,
楽しいみ。。。
09:25迄、へやにあっている，laptop でこのことばがかく。
[14:24] じもしょへ行きます

「今　九月八日，これ　から　きのう「九月七日」　つづく　話」

[16:30]位、プレレト行く
[17:30]位、きた
始めてだからたぶん。賑やかなのに、ひとごみにあわせらなかった、外人　みたい、俺は
でも、色色あったんだ、少し楽しかった。。。
ああ、忘れちゃった、昨日の昼ご飯は鶏肉、飲むものはコラクとおちゃ
コラクのんだあとおいのりしました、四人と一緒に、
あとで、つづく　昼ご飯をたべた、
人はが二十人ぐらいあるけど五人がしってるだけ，
[20:30] アパトへかいえった

This is a problem that I have [I'm using Inkscape]
Please look at this picture below
In this article I call this original font

and I want to change into shape like this

So I run my “Text and Font” Toolbar  and

change family font into japanese font type

but after I pressed apply it turn into like this

and on the canvas it look like this

今日　げんようび,　十九　十一月　二〇〇七

Those are my japanese’ writing using SCIM and SKIM.

SCIM also has plenty of language that have been supported.

such Amharic, Arabic , Bengali, Gujarati, Japanese, Hindi, Kannada, Korean, Malayalam, Rusian, Punjabi, Tamili, Telugu, Thai, Vietnamese, Chinese (Simplified), Chinese (Tradisional, and other……….

And SKIM supported

zh_TW.Big5,zh_TW,zh_HK.Big5-HKSCS,
zh_HK,zh_CN.GB18030,zh_CN.GBK,zh_CN.GB2312,zh_CN,
ja_JP.eucJP,ja_JP.ujis,ja_JP,ko_KR.eucKR,ko_KR

————————————————————————————————————————————-

[[PACKAGE REQUIRED]]

- scim-1.4.7.tar.gz

- scim-tables-0.5.7.tar.gz

- skim-1.4.5.tar.bz2

- anty-9100.tar.gz

- scim-anthy-1.2.4.tar.gz

———————————————————————————————

[[SUPPORT PACKAGE REQUIRED]]

- checkinstall

note: you could find checkinstall-*.tgz on the Slackware 11.0 on “extra” package include on Slackware 11.0 DVD, or you get it from this site

http://packages.slackware.it/browse.php?q=11.0/extra

[[HOW TO INSTALL]]

[checkinstall]

# installpkg checkinstall-1.6.0-i486-2.tgz

[scim]

# tar zxf scim-1.4.7.tar.gz

# cd scim-1.4.7

# ./configure

# make

# checkinstall

# installpkg scim-1.4.7-i386-1.tgz

[scim-tables]

# tar zxf scim-tables-0.5.7.tar.gz

# cd scim-tables-0.5.7

# ./configure

# make

# checkinstall scim-tables-0.5.7-i386-1.tgz

[skim]

# tar xjf skim-1.4.5.tar.bz2

# cd skim-1.4.5

# ./scons

# ./scons install

[anthy]

# tar zxf anthy-9100.tar.gz

# cd anthy-9100

# ./configure

# make

# checkinstall

# installpkg anthy-9100-i386-1.tgz

[scim-anthy]

# tar zxf scim-anthy-1.2.4.tar.gz

# cd scim-anthy-1.2.4

# ./configure

# make

# checkinstall

# installpkg scim-anthy-9100-i386-1.tgz

[ Configurations ]

Log in as your user (if you want user can use skim)
If you want your root can run the skim, please log in as “root”

Edit file ~/.xinitrc

# vi ~/.xinitrc
put these lines on before “startkde” commands

export XMODIFIERS=”@im=SCIM”

export LC_CTYPE=”ja_JP.ujis”

export GTK_IM_MODULE=”scim”

export QT_IM_MODULE=”xim”

Log in as root

Edit file /etc/gtk-2.0/gtk.immodules
# vi /etc/gtk-2.0/gtk.immodules

put these lines on /etc/gtk-2.0/gtk.immodules

“/usr/lib/gtk-2.0/immodules/im-scim.so”

“scim” “SCIM” “gtk20″ “/usr/share/locale” “ja:en:th:zh:ko”

Log in as “root”
Edit file /etc/rc.local
# vi /etc/rc.local
put these lines

scim

skim

Restart your PC

To run the skim press Ctrl+Space
In this experiment, I only managed to get one language works besides
english, this happen to SKIM but SCIM manage to use all language that provided by scim-tables and anthy

On SKIM, if you want to change the language, you can change the
LC_CTYPE environtment
with one of these languages that been supported

zh_TW.Big5,zh_TW,zh_HK.Big5-HKSCS,
zh_HK,zh_CN.GB18030,zh_CN.GBK,zh_CN.GB2312,zh_CN,
ja_JP.eucJP,ja_JP.ujis,ja_JP,ko_KR.eucKR,ko_KR

This article is my experience when I installed gforge on my debian systems

Before install the gforge there are several things that must set up first
These is what I had done

For you who using a standalone PC and a server which is not registered yet on internet or on their local networks

Login as a root

First.

set your hostname at /etc/hostname into nameserver you want
on this example I used

awaludin.org

Second

Install and configure the dns server

# apt-get install bind

Configure dns server

add these lines into /etc/bind/named.conf

zone "awaludin.org" {
	type master;
	file "/etc/bind/awaludin.org";
};
zone "177.13.10.in-addr.arp" {
	type master;
	file "/etc/bind/177.13.10.reverse";
};

Create file /etc/bind/awaludin.org

# vi /etc/bind/awaludin.org

and put these lines into /etc/bind/awaludin.org

 ; ——————————————————-
$TTL    604800
@       IN      SOA     awaludin.org. root.awaludin.org. (
		1           ; Serial
		604800         ; Refresh
		86400         ; Retry
		2419200         ; Expire
		604800 )       ; Negative Cache TTL
;
@       IN      NS       awaludin.org.
@       A       10.13.177.60
www     A       10.13.177.60
scm     A       10.13.177.60
lists   A       10.13.177.60

Create file /etc/bind/177.13.10-reverse

# vi /etc/bind/177.13.10-reverse

and put these lines into /etc/bind/177.13.10-reverse

; ———————————————————
$TTL    604800
@       IN      SOA     awaludin.org. root.awaludin.org. (
		1         ; Serial
		604800    ; Refresh
		86400     ; Retry
		2419200   ; Expire
		604800 )  ; Negative Cache TTL
;
@       IN      NS      awaludin.org.
60      IN      PTR     awaludin.org.
60      IN      PTR     scm.awaludin.org.
60      IN      PTR     lists.awaludin.org.

Check every configurations

# named-checkconf /etc/bind/named.conf
# named-checkzone awaludin.org /etc/bind/awaludin.org
# named-checkzone 177.13.10.in-addr.arp /etc/bind/177.13.10.reverse

Start the services

# /etc/init.d/bind9 start

and if it already runs, restart it

# /etc/init.d/bind9 restart

Third

Install the mod-ssl and create the certificate

# apt-get install libapache-mod-ssl
# mod-ssl-makecert

When you’re making a certificate there is step when you are asked for phrase , please remember this phrase carefully , because when you start or restart apache server , it will demand the phrase

Fourth

Set up your hosts at /etc/hosts
add these lines into /etc/hosts

10.13.177.60	awaludin.org
10.13.177.60	www.awaludin.org
10.13.177.60	scm.awaludin.org
10.13.177.60	lists.awaludin.org

Fifth

Install proftp and configure it

# apt-get install proftpd

Please read the dialog carefully during the installation, choose “inetd”

Edit /etc/proftpd/proftpd.conf and find this line

UseIPv6				on

And change it into

UseIPv6				off

Restart the proftpd to take effects

# /etc/init.d/proftpd restart

Sixth

WARNING !!!

If you had a web files before, probably it won’t work well, because gforge systems edit the “include_path” on php.ini
If you want your web run smoothly, please make virtual hosts
and you could consulate it with me, perhaps I could help.

Seventh

Install apache’s modules

The modules that needed here is libapache2-mod-php and libapache2-svn
you could use libapache2-mod-php5 or libapache-mod-php4

# apt-get install libapache2-mod-php4
or
# apt-get install libapache2-mod-php5

# apt-get install libapache2-svn

Activate the module that had been installed

# a2enmod php4
or
# a2enmod php5

# a2enmod dav_svn

Eighth

Install gforge

# apt-get install gforge

During the installation, you will asked for your gforge admin password, fill it and don’t you musn’t forget it.
Follow the installation carefully, When the phrase asked to you fill with the sama phrase when you make certificate before

If you enter a wrong phrase it will asked the phrase again
but If the phrase you entered is right but it’s said “failed”. It is mean you have patch this patch below (notice: please change a text “awaludin.org” on the patch into your own domain name)

here is the patch:

--- /etc/gforge/httpd.conf	2007-09-28 14:08:56.000000000 +0700
+++ /root/pacth/httpd.conf	2007-09-28 14:07:23.000000000 +0700
@@ -248,78 +248,6 @@
   ServerName lists.awaludin.org
   AddHandler cgi-script .cgi

-  ScriptAlias /mailman/ /var/lib/mailman/cgi-bin/
-
-  Alias /pipermail /var/lib/mailman/archives/public
-
-    AllowOverride Options
-    Options FollowSymLinks
-
-
-  Alias /images/mailman /usr/share/images/mailman
-
-    order allow,deny
-    allow from all
-
-
-  RedirectMatch permanent ^/$ http://lists.awaludin.org/mailman/listinfo
-  LogFormat "%h %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" gforge
-  CustomLog "|/usr/bin/cronolog /var/log/gforge/%Y/%m/%d/gforge.log" gforge
-  # Ensure that we don't try to use SSL on SSL Servers
-
-    SSLDisable
-
-
-
-# HTTPS
-
-  ServerName lists.awaludin.org
-  AddHandler cgi-script .cgi
-
-
-    SSLEngine on
-    SSLCertificateFile /etc/apache/ssl.crt/server.crt
-    SSLCertificateKeyFile /etc/apache/ssl.key/server.key
-
-      SSLOptions +StdEnvVars
-
-
-      SSLOptions +StdEnvVars
-
-    SetEnvIf User-Agent ".*MSIE.*" nokeepalive ssl-unclean-shutdown
-
-
-
-    SSLEnable
-
-
-  ScriptAlias /mailman/ /var/lib/mailman/cgi-bin/
-
-  Alias /pipermail /var/lib/mailman/archives/public
-
-    AllowOverride Options
-    Options FollowSymLinks
-
-
-  Alias /images/mailman /usr/share/images/mailman
-
-    order allow,deny
-    allow from all
-
-
-  RedirectMatch permanent ^/$ https://lists.awaludin.org/mailman/listinfo
-  LogFormat "%h %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" gforge
-  CustomLog "|/usr/bin/cronolog /var/log/gforge/%Y/%m/%d/gforge.log" gforge
-
-
-#
-# List host
-#
-# HTTP
-
-  ServerName lists.awaludin.org
-  AddHandler cgi-script .cgi
-
   ScriptAlias /cgi-bin/mailman/ /var/lib/mailman/cgi-bin/

   Alias /pipermail /var/lib/mailman/archives/public

Save the patch into /home/httpd.conf.patch

# cp /etc/gforge/httpd.conf /etc/gforge/httpd.conf.backup
# cd /etc/gforge
# patch -p3 < /home/httpd.conf.patch

Restart apache2 server

# /etc/init.d/apache2 restart

If your server not running, please send your /etc/gforge/httpd.conf .backup to me at xblank_id@yahoo.com

If the server works well
open the browser and type “http://awaludin.org” (please type the url according to your own domain setting at /etc/hostname)

Login as admin and enter the password that you have made during the gforge installation (at step Eighth)

you still couldn’t use svn because we have’nt installed gforge-plugin-scmsvn yet

try it yourself

perhaps I will cover it up someday with this article next part

to be continued…………..

I’d some trouble when I was running my firefox,
it said that

*** glibc detected *** double free or corruption (out): 0×089e1478 ***

I decided to install a new one and new higher version then before
but I also get an error

** glibc detected *** free(): invalid pointer: 0×08b82d38 ***

I thougt it was “my fault when I changed my kernel” who responsible for this problems
but I was wrong.
after suring on internet and find what’s going on with my firefox.
I found many article using a keyword

“*** glibc detected *** double free or corruption ( firefox”

So I pick up one by one randomly,
I found one who has same problem with mine, and I tried to implemented it

after I tried, and the problem had solved
the thing I do is change the “GTK_IM_MODULE” into “xim”

# export GTK_IM_MODULE=”xim”
It was my fault “when I changed my GTK_IM_MODULE environtment into scim” when I experimented SCIM and SKIM.

because I want to use both firefox and scim so I decided to make a shell
script

this is the script I made
———————————————————–
#!/bin/bash

export GTK_IM_MODULE=”xim”
/usr/bin/firefox &
export GTK_IM_MODULE=”scim”
—————————————————————

I hope it’ll hopefull for everyone….

see ya next time

がんばって

また あした

Situs ini dibuat tanggal 24 Agustus 2007